Drifting happens when you approach a corner with speed. The bike leans over to turn and loses traction. Your bike will slide as the momentum pulls it out of the corner. As you sling the rear of your mountain bike, the back tire will skid. This is a rad move that requires consistent practice, especially if you are a beginner.
Do you want to learn the fundamentals to drift bicycle? Keep on reading and we’ll share some tips that will help you do it like a pro. It is a maneuver that requires practice, so do not fret if you are not able to do it in an instant.
A Step-by-Step Guide on How to Drift Bicycle
For beginners, learning how to drift a bike can be an intimidating thought. It requires extensive skills. With a single wrong move, you can crash. Below are some of the most important steps to help you do it correctly.
Before anything else, gear up for your safety. Taking safety precautions will limit the likelihood of an injury in case of a crash. As a beginner learning the basics of drifting, expect that you will make mistakes and an accident will happen.
A mountain bike helmet is non-negotiable when it comes to the safety gear that you need to have. MTB knee pads and elbow pads will also help to prevent scraping or damaging your skin when you crash. To protect your hands, wear MTB gloves.
1. Pedal Quickly When Approaching a Turn
Assume the right position. Do not crouch too much as this can put unnecessary strain on your back. Position your hands properly in the MTB handlebars. Make sure to stay relaxed so that you can easily control the bike. Otherwise, you will be too stiff and you will have a hard time maneuvering the bike in the right direction.
When getting ready to drift bicycle, you need to pedal quickly as you approach a turn. Your legs will be the source of most of the power. The faster you are as you approach the turn, the easier it will be for the rear tire to skid. It would be best if you are coming from a downhill, as this will help you go faster.
While you should go fast, you should also avoid over-speeding. You can over-rotate and fall. On the other hand, if you are too slow, you will not drift.
Pro Tip: Before pedaling quickly and skidding, take note that doing so can damage the trails, especially when wet. Avoid doing this in public trails.
2. Lean Once You Reach the Turn
Once you reach the point at which you will turn the bike, lean at 45 degrees. Do this in the same direction of the turn. Meaning, if the turn is to the left, then you should also be leaning on your left side.
Avoid leaning too much. This can result in loss of control. If you are leaning too low, you are risking falling off the bike. You will also find it hard to go back to your original position once you are through the turn.
While you are turning, keep an eye on the peak of the curve. Doing this will make it easier to steer the bike in the right direction. If you look at the ground, you will end up disoriented, making it more difficult to decide what to do next once you are done with the turn.
3. Shift Your Weight Over the Handlebars
As you go around the turn, shift your weight forward, over the handlebars. This is done by simply leaning to the front. The goal is to lighten the load on the rear wheel of the bike. This is what will let it skid on the ground.
At the start of the turn, you will feel that the back wheel is already skidding. If you need the tire to break loose, engage the rear brake.
4. Extend Your Inside Foot
To drift, you will need to extend your inside foot so that it will hover slightly above the surface. This is a necessary move to retain balance and control. Keep this position until the bike completes the turn.
5. Go Back to an Upright Position
The last step on how to drift a bike is to shift the weight of your body to its original position. Earlier, during the drift, you were leaning at 45 degrees to the ground. After the turn, the rear MTB wheel must have already regained traction and you should be in your original riding position.
Q: Can you drift a bicycle?
Yes, you can drift a bike. For beginners, it is easier said than done. It requires special skills, which can take time to learn. You need to learn how to lean your body properly as you pivot. You must also learn how to balance the bike so that you won’t crash as you drift. It is also important to choose a wide turn so that it will be easier to drift.
Q: How do you drift a mountain bike?
To drift a mountain bike, pedal quickly as you approach the turn. Then lean your body at 45 degrees and shift your weight. Extend your inside foot and once you are out of the turn, bring your body back to its original position.
Globo Surf Overview
Learning how to drift bicycle can be intimidating for beginners. When not done properly, you can end up crashing! To drift like a pro, pedal quickly when approaching a turn. Speed is important to gain momentum. Once you turn, lean your body and shift your weight. Extend your outside foot and resume your original position once you are over the turn.